Fab Industries, Inc. · Houston, Texas

Repairs: Field & Shop

Repairs in the field or in our Houston shop, with fast turnaround, since 1982.

Repairs

Repairs Where You Need Them

When equipment fails, it needs to be back in service quickly. Fab Industries repairs oil and gas equipment in the field or in our Houston shop, with fast turnaround.

Fab was founded in 1982 refurbishing Daniel Senior Orifice meters, giving equipment a second life instead of scrapping it. More than 40 years later, repair is still a core part of our shop. Our qualified welders, machinists and assembly and test crews work under one roof in a 40,000-square-foot shop with overhead cranes from 10 to 50 tons, so the work is done in-house before it ships.

Field or Shop

In the field

Our crews can repair equipment at your site. We provide 24-hour service to the Gulf Coast region.

In our shop

Equipment that needs machining, welding or a full rebuild comes into our shop, where it is taken apart, repaired, reassembled and tested. We ship worldwide.

Orifice Fitting Repair & Rebuild

Why condition matters

An Orifice meter calculates flow from the differential pressure across a thin plate with a precisely bored opening. The Orifice fitting holds and seals that plate concentric in the meter tube, with the pressure taps on each side. Single-chamber fittings require the line to be depressurized to change the plate; dual-chamber fittings let the plate be removed while the line stays in service.

Measurement depends on the plate sitting square and concentric in a clean, round bore. Worn seals, damaged plate carriers, leaking valves or a damaged bore can bias the measurement or make plate changes unsafe or impossible.

How we repair and rebuild a fitting

The work depends on the fitting’s condition. A typical repair includes:

  • Cleaning and disassembly
  • Inspection of the body, bore, plate carrier, seals and operating parts
  • Micing (measuring) the bore and meter tube to check them against AGA Report No. 3, Part 2
  • Replacement of seals, gaskets and worn parts from our parts stock
  • Weld overlay and machining to restore worn sealing surfaces to dimension
  • Reassembly, hydrostatic testing and leak checks before the fitting ships

We keep a deep stock of meter parts from 2″ to 12″, plus parts and repair kits.

Meter Tube Repair

A good fitting needs a good meter tube. We clean and mic meter tubes, repair and refurbish worn or damaged tubes, and fabricate new ones when repair is not the right answer. See AGA 3 Orifice Meter Tubes.

Hydrostatic Testing In-House

Repaired pressure-containing equipment is hydrostatically tested in our shop before it goes back in service. The equipment is filled with water, brought up to the required test pressure, held, and checked for leaks. Because the testing is done in-house by the same crews that did the repair, any problem found can be corrected in the shop before the equipment ships.

Beyond Meters

Repair at Fab is not limited to meters. Our welders and machinists also take on welding, remanufacturing and machining work on other oil and gas equipment. Please contact us with any questions about work not listed here.

For after-hours emergencies, call 713-748-0799.

For a quote, email sales@fabindustriesinc.com with a description of the equipment and the problem, photos if you have them, required dates and the location, or call 713-748-0799 (toll-free 800-227-6944). For anything else, email contactus@fabindustriesinc.com.

Planning a LACT Unit?

Request a quote, email sales@fabindustriesinc.com, or call 713-748-0799 or toll-free 800-227-6944. We provide 24-hour service to the Gulf Coast region.

×
img

    Request a Quote

    Contact Info

    Phone number

    800-227-6944

    713-748-0799

    Email address

    Sales & Quotes: sales@fabindustriesinc.com

    General Inquiries: contactus@fabindustriesinc.com

    Address info

    6322 Long Dr. Houston, TX 77087